Quality is now available at every corner

Date: 23 July 2014

LiSEC has re-engineered the vertical sealing machines of the VFL series. The result is clear. With the new VFL system, dubbed "CleanSeal", even less effort is required overall to eliminate or prevent dirt, and the sealing quality of the corners is considerably improved.

This results in significantly reduced production times.   



Perfectly sealed corners on triple insulating glass without any manual remake required.

The self-learning CleanSeal got off to a clean start


When developing the CleanSeal, the focus was put on increasing the overall quality of the end product. A key factor here was the level of material spreading that occurs. In conventional systems sometimes - depending on the operator's experience and instinct - too much sealant is applied around the corner. This excess material can lead to contaminate the units and the transport device. The solution: LiSEC developed a highly-dynamic, self-regulating, servo-controlled mixing/metering system. "Instead of designing a system that is 'more resistant to contamination', we developed a solution that ensures that less contamination is produced", said Alexander Kronsteiner, Head of Product Management at LiSEC. The new mixing/metering system detects temperature fluctuations and changes in viscosity caused by the differences between batches, etc. or by downtimes, and is self-adjusting, making manual re-adjustment unnecessary if changes occur. The new stationary mixing/metering unit enables precise metering without material slippage thanks to a large material flow range (up to 1:10). Kronsteiner continued: "All in all, we improved the mixing/metering quality tenfold".

The developers took a further step towards contamination thanks to optimised centering (positioning) of the glass sheets, which also results in considerably less glass breakage.



The easily accessible mechanism allows quick and easy change of material.

The perfectly sealed corner – faster and with less effort


The CleanSeal concept also includes a re-design of the corner rollers for optimum material distribution in the corner area. "Until now, its function was more to correct the corners, and now it's advanced to finishing corners", said Kronsteiner. The entire system is so cleverly devised that a single operator can complete all of the steps. In particular, the process for "dabbing the corners" has been almost completely eliminated.

The LiSEC engineers also optimised the user guidance and made the settings even easier, such as the self-calibration of the depth scanner for changing nozzles and material. They also developed the automatic flush and mixing process via pressure progression measurement. The number of parameters has been reduced and the recipe tree minimised. This makes it easier to operate and results in shorter computing times. Kronsteiner: "All the optimisation measures allow for shorter cycle times. With triple units from 1200 to 800 mm, the cycle time is now only 33 seconds.” The pneumatic coupling device between the system and the material line is not only ergonomic, it also ensures a simpler exchange of materials.



CleanSeal features highly dynamic volume control.

Deliberately robust.


The CleanSeal metering unit is a robust solution. LiSEC relied on proven technologies to make sure of this. For example, instead of wear-prone gear pumps that are comparably expensive and inaccurate, it utilises a servo-controlled throttle valve. Sealing material is applied as long as possible with open controllers. The material is optimised and controlled through the open flow and the material flow is only throttled in the corner area. In addition, there is no dynamic mixer, but rather a shortened mixing section featuring significantly reduced material consumption during rinsing.

About LiSEC

LiSEC, with headquarters in Hausmening/Amstetten, is a globally active group that has provided innovative individual and complete solutions in the field of flat glass production and finishing for more than 50 years. The business activities encompass machines, automation solutions and services. In 2013 the group generated a total turnover of around 200 million euros with around 1,600 employees and over 30 sites, with an export quota of more than 90 percent.

LiSEC develops and manufactures glass cutting systems and sorting systems, individual components and complete production lines for insulation and laminated glass production as well as glass edge machining systems and pre-stressing plants. With reliable technology and intelligent automation solutions LiSEC sets the standard in quality and technology, contributing significantly to the success of their customers.

Press contact:

Filip MIERMANS Head of Corporate Communications LISEC Austria GmbH Peter-Lisec-Str. 1 – 3353 Seitenstetten Tel.: +43 7477 405-1151 filip.miermans@lisec.com – www.lisec.com

600450 Quality is now available at every corner glassonweb.com

See more news about:

Others also read

Coinciding with the fulfillment of the ARTESUN project´s first year (November), the third Project Meeting took place at Corning headquarters in Avon, France    Funded by the European Comission through its Seventh Framework Programme, ARTESUN Project aims to develop organic photovoltaic solar cells (OPV) through the implementation of three full-scale prototypes.
"Opportunity in the Indian Glass Market - 2014 : Market size, Market share, Market landscape, Market trend analysis, Growth drivers, Future opportunity, Future forecast" provides an insight into the Indian Glass current market scenario, structure and practices.
Dubai Investments (DI) CEO Khalid Bin Kalban has revealed that the Company seeks to examine several expansion opportunities in 2015.
This report was created for strategic planners, international executives and import/export managers who are concerned with the market for nonwired glass sheets of float glass and surface ground or polished glass.
New Business to Support Company's Growing Presence in East and Central African Markets - H.B. Fuller Company (NYSE: FUL) announced today that it has signed an agreement to purchase Continental Products Limited, a provider of industrial adhesives in East and Central Africa.
CITIC Capital Partners (“CITIC Capital”), the private equity arm of CITIC Capital Holdings Limited, is pleased to announce that it has agreed to sell all of the shares of Narumi Corporation (“Narumi”) held by its funds to Ishizuka Glass Co., Ltd. (“Ishizuka Glass”).

Add new comment